Setup guide · Ezlo AI

Smart Indoor Christmas LED Strip Kit

Quick start guide and user manual. A Wi-Fi LED strip kit that works with the Ezlo AI app. No hub needed.

9.8 ft (3 m)16.4 ft (5 m)24 ft (7.3 m)
QUICK START
  1. Plug in the kit.
  2. Open the Ezlo AI app, tap Devices, then +, then EzloPi.
  3. Tap Scan now, then Adopt.
  4. Connect the kit to your 2.4 GHz Wi-Fi.

That's it. Your lights are ready.

What is in the box

Everything is already wired and set up. There's nothing to solder and no hub to buy.

In the box

  • LED strip, connected to the controller
  • Wi-Fi LED controller
  • 24 V power supply, sized for your kit
  • Quick start guide

What you need

  • An iPhone with the Ezlo AI app, from the App Store. Android phones are not supported yet.
  • Bluetooth turned on, on your phone. The app finds the kit over Bluetooth.
  • Your home Wi-Fi name and password. The kit works on 2.4 GHz Wi-Fi with a password. It does not support 5 GHz or open networks.
  • A wall outlet near the spot where you want the lights. Indoor use only.
GOOD TO KNOWNo Ezlo hub is needed. The kit connects straight to your Wi-Fi. If you already have Ezlo devices, the lights show up next to them in the same app.

Specifications

Three lengths. Same strip, controller and app.

9.8 ft
3 m strip
Segments
42
Power supply
24 V DC, 48 W
16.4 ft
5 m strip
Segments
70
Power supply
24 V DC, 72 W
24 ft
7.3 m strip
Segments
105
Power supply
24 V DC, 120 W

LED STRIP

Type
Addressable RGBCCT COB strip (WS2811)
Colors
Full color, plus warm white and cool white
LEDs
840 per meter, dotless light
Segment length
2.8 in (71.5 mm), each segment controlled on its own
Width
0.4 in (10 mm)
Beam angle
180°
Color rendering
CRI above 90
Input
24 V DC
Rating
IP30, indoor use only
Mounting
Self-adhesive backing

CONTROLLER

Connectivity
Wi-Fi 2.4 GHz; Bluetooth for setup
Input
24 V DC
Size
4.6 × 1.8 × 0.6 in (118 × 45 × 15 mm)
Operating temperature
14 to 104 °F (−10 to 40 °C)

POWER SUPPLY

Input
100–240 V AC, 50/60 Hz
Output
24 V DC; 48 W, 72 W or 120 W by kit

GENERAL

App
Ezlo AI, iPhone (iOS)
Hub
Not required
Warranty
1 year

Get to know your kit

Three parts, already connected. You only plug in the power.

LED strip

  • Runs color, warm white and cool white.
  • Each 2.8 in segment lights on its own, so colors can chase, fade and blend along the strip.
  • Self-adhesive back for mounting.

Wi-Fi controller

  • Sits between the strip and the power supply.
  • Joins your 2.4 GHz Wi-Fi so the app can reach the lights.

Power supply

  • Plugs into a standard wall outlet.
  • Sized for your kit's length. Use only this one.

Ezlo AI app

  • Adds the kit, turns it on and off, sets brightness, color and effects.
  • Ezlo AI creates effects from a sentence, by voice or text.
1

Add your kit in the Ezlo AI app

Do this before you mount the strip, so you know everything works. Keep your phone within 6 ft (2 m) of the controller.

  1. Plug the power supply into the controller, then into a wall outlet.If the power supply is already connected to the controller, just plug it into the outlet.
  2. Download Ezlo AI from the App Store, open it and sign in. Create an account if you don't have one.
  3. Tap Devices in the tab bar, then + at the top right.
  4. Under "What are you adding?", tap EzloPi.
  5. Tap Scan now.The app looks for your controller over Bluetooth.
  6. When your controller appears, tap Adopt.
Devices screen with the + button
1Tap + on Devices.
What are you adding? screen with EzloPi
2Tap EzloPi.
Scan for devices screen
3Tap Scan now.
  1. Check the device information and tap Next.
  2. Pick your Wi-Fi network. Your phone's network is already selected.Use a 2.4 GHz network with a password. 5 GHz and open networks don't work.
  3. Type your Wi-Fi password and tap Continue.
  4. Wait while the app sets up your kit.It joins your Wi-Fi, gets online, adds the kit to your account and connects to Ezlo.
  5. When you see "Successfully added!", tap Try your lights.Or tap Go to Dashboard to finish.
Detected devices screen with Adopt
4Tap Adopt.
Wi-Fi network picker
5Pick your 2.4 GHz Wi-Fi.
Successfully added screen
6Done. Try your lights.
2

Mount the strip

Mantels, bookshelves, indoor window frames, TV consoles. Pick a clean, dry, indoor spot near an outlet.

  1. Unplug the power supply from the outlet.
  2. Plan the run. Start at the controller end, near the outlet.Lay the strip out first to check that the length fits.
  3. Clean the surface and let it dry.The surface should be smooth, dry and non-flammable.
  4. Peel the backing off slowly, a little at a time.Pulling too hard can stretch or tear the tape.
  5. Press the strip down along its edges, not on the lights.Pressing on the LED surface can damage it over time.
  6. Plug the power supply back in.
CORNERS AND BENDS
  • Bend the strip gently, no tighter than 1.2 in (30 mm).
  • Don't fold, crease or bend it sideways.
DON'T
  • Cut, extend or join the strip.
  • Leave it coiled on the reel while it's on.
  • Cover it or mount it behind insulation.
3

Use your lights

Your strip appears on the Home tab, under "Lights, LEDs & switches".

On and offTap the power button on the strip's tile.
ControlsTap the tile to open them.
BrightnessDrag the Brightness bar.
ColorTap a circle under Colour.
EffectsTap Effects and moods, then pick a look such as Rainbow, Colour wipe or Breathe. Use Speed and Intensity to fine-tune it.
Light up when Ezlo AI talksThe strip moves with Ezlo AI's voice, then goes back.
Home PulseShows the home's rhythm on the strip.
Home tab with the LED strip tile
1Tap the power button.
Brightness and color controls
2Brightness and color.
Effects and moods
3Pick an effect.
4

Ezlo AI, schedules and automations

Your lights are the start. Ezlo AI makes them yours.

Ask Ezlo AI

Tap Ask Ezlo in the tab bar and ask by voice or text to create your own effect. Try saying:

"Make a slow red-and-white candy cane effect.""Turn off the Christmas lights."

Schedules

Use Automate to turn the lights on at sunset and off at bedtime. Set it once and it runs every day.

Grows with your home

Add more Ezlo devices to the same app, such as smart plugs for your tree lights, and put everything on one schedule. Some devices need an Ezlo hub. The device page says when one is required.

5

Troubleshooting

Tap a problem to see what to try.

The app doesn't find the controller

Turn on Bluetooth on your phone. Stand within 6 ft (2 m) of the controller. Unplug the power supply, wait 10 seconds, plug it back in and tap Scan now again.

The kit doesn't join Wi-Fi

Pick a 2.4 GHz network with a password. Check the password (tap the eye to see it). Move the router or the kit closer together and try again.

The far end of the strip looks dimmer

Normal at full white on longer strips. Lower the brightness or pick a color.

The lights don't turn on

Check that the power supply is plugged into the outlet and into the controller. Check the strip's connector at the controller.

The strip shows offline in the app

Check that your Wi-Fi is working. Unplug the power supply for 10 seconds and plug it back in.

6

Safety and warranty

Please read before you install or use the kit.

IMPORTANT SAFETY WARNING
  • For indoor use only. The strip is rated IP30 and the controller and power supply are not waterproof. Keep every part away from rain, snow, moisture and wet surfaces.
  • Use only the power supply that comes in the box. It's sized for your kit's length. Don't connect extra strips or extend the strip.
  • Don't cut, splice or re-solder the strip. The kit is wired and set up before it ships, and changes can damage it or create a fire risk.
  • Let it breathe. Don't use the strip coiled on its reel, covered, or behind insulation. Mount it on a clean, dry, non-flammable surface.
  • Check before use. If the strip, cable, controller or power supply is damaged, unplug it and don't use it.
  • Unplug before handling. Disconnect the power supply from the outlet before you install, move or clean the lights.
  • Not a toy. Keep small parts and cables away from children and pets.

Warranty

Your kit is covered by a 1-year limited warranty from the date of purchase. Contact Ezlo support for help or a replacement.

Need help setting up your kit?

Our customer care team is available Monday to Friday, 6 AM to 8 PM ET, and Saturday and Sunday, 8 AM to 7 PM ET. International: 702 487 9770